How To Make A Hemp Necklace The Hippie Way With Insider Tips And Tricks

Materials to make a hemp necklace.ring then I attach the shower ring to a hook or
Hempwall. I then take the center string and tie it to one
Beadsof the belt loops on my pants.a) Take your two
Scissorsknotting cords. Pull them to opposite sides of the
Optional materials.center string.
GlueThe basic knot is called a square knot. It can be
Shower ringstarted from the left or from the right.
Step 1. Cut your hemp cord.a) Cut two cordsTheir are two designs that can be created spiral
that are 5 feet 8 inches in length. This is going toand flat.
be your knotting cord.The flat design is created when you alternate
Tip - I don't whip out a tape measure every timeyour knots. Left, right, left, right or right, left,
I need to measure my hemp. I measure it againstright, left.
myself. I pull it out to the width of both my armsThe spiral design is created when you tie the
spread to their max and cut it their. It's muchsame knot. Left, left, left, left or right, right, right,
quicker than measuring it with a tape measure.b)right.
Cut one thread or thin cord that is 2 feet 10It doesn't matter which knot you start with it
inches in length. This is going to be your centermatters which knot you follow up with.
string. If you are using beads the will go on thisTying a left knot.a) To tie a square knot starting
string so make sure they fit. I measure it fromon the left you take the cord on the left and lay
my finger tips to my neck.it over the center string creating a loop on the
Tip - I like to use more hemp than I need. It'sleft.b) Next take the cord on the right and go
always easier to cut a little bit off than to fix theover the left cord then under the center string
necklace if their isn't enough.and up threw the loop on the left of the center
Step 2. Starting out.a) Take the two knottingstring.c) Pull tight.
cords they are the thicker and longer cords andTying a square knot starting on the right involves
tie them together using an over hand knot. To dothe same process started on the right side of the
an over hand knot make a loop go threw thenecklace.
loop and pull tight.b) Take the shorter thinnerWhen you are ready for a bead move the bead
center string and both knotting cords and tieup behind the last knot you tied then tie your
them together using an over hand knot twonext knot on the other side of the bead.
inches from where you made your first overContinue tying knots and adding beads until you
hand knot.c) Braid all three cords together forget to your desired length.
about 2 inches. Then tie them off with an overI usually stop a necklace when the macrame and
hand knot.bead portion is long enough to stretch around my
Step 3. Add beads.a) Add the beads you want toneck and touch ends.
use.Finish the macrame portion of the necklace by
Tip - If it's hard to push the center string threwtying all three cords together in an over hand
the beads because they have small holes. Place aknot.
drop of general purpose glue on your index fingerStep 5 finishing the hemp necklace.a) Braid all
then position the center string on the glue 4three cords together for about 2 inches. Then tie
inches from the end and pinch in place with yourthem off with an over hand knot.b) Cut off the
thumb. Then pull the string threw your thumb andremaining length of the center string.c) Take the
index finger distributing glue along the final fourtwo knotting cords and tie them together using
inches of length. If some areas are still dry repeat.an over hand knot.d) Cut off any remaining length
Hang the glued end in the air to dry for thirtyand you are done.
minutes to an hour or until hard.Tip - The braided portion and loop on the end is
Step 4. Macrame.for tying it off. You give them 4 inches of braid
Tip - The knots are much quicker and easier toand four inches of loop so that they can tie it off
tie if the center string is tight. So I take the loopto the length they desire and dispose of the rest.
that I created in step two and put it on a shower